Sometimes it gets stuck in the corner of the pool by the steps; other times it goes in circles. … This is most likely caused when pool cleaners are left in the pool 24/7. When the water is cold or cools off from a warm day, the plastic in the hose gets a memory and curls slightly.
Keeping this in consideration, What’s the difference between a Polaris 360 and 380?
From Polaris Website, 380 requires a booster pump, 360 requires a dedicated pressure line without an additional pump: Powered by triple jets and a separate booster pump, the Polaris 380 is one of our most powerful, durable cleaners and is suitable for all in-ground pools.
Secondly Why does my Polaris 65 go in circles? If your Polaris 65 is turning in a circle continuously rather than being random left or right, the randomizer ball is not coming free from the steering port. Being stuck means there is too much leakage into the steering section when the flow should be minimum.
Why is Polaris on its side?
Polaris 280 Leans to One Side. leans to one side while it is running, there are a few basic reasons this happens. is filled with water. If the head float develops a crack that allows water to fill the float, it gets heavy and the cleaner will run on its side.
Table of Contents
Does a Polaris 380 need a booster pump?
The Polaris Vac-Sweep 380 pressure cleaner works in all in-ground pools, and requires a booster pump.
Which Polaris does not require booster pump?
The Polaris Vac-Sweep ® TR36P features advanced technology; cleaning without the need for a separate booster pump. It vacuums, sweeps and scrubs the bottom and walls of any size or shape pool.
How does a Polaris 65 work?
Patented jet sweep assembly blows water against the pool wall to loosen debris in hard-to-reach places and then sweeps it into an easy-to-remove filter bag. Powered by the pressure of clean water returning to your pool, leaving both the filter and skimmer free to eliminate contaminants.
Why does my Polaris 360 float?
Why is Polaris 360 floating? Leaks in the Polaris hose cause the cleaner to lose pressure, allowing it to float above the pool bottom. To check for leaks, turn the system on and pull the hose out of the water one section at a time, looking for bubbles or trickles of water.
Can I leave my Polaris in the pool?
No problem with leaving the Polaris in the pool when not in use. run the 280 for as long as it keeps the pool clean, this could be 1 hour per day to 6 hours per day depending on the amount of debris is in the pool, but remember the 280 has gears and cogs so the more you run it the quicker it will wear out.
Why does my Polaris 360 run on its side?
360 Running in Circles on Its Side
If the 360 falls onto its side, the filter bag may be full. Empty the bag and resume normal operation of the cleaner. If emptying the bag does not solve the problem, remove the head float from the back of the machine and shake it.
How do I know which Polaris?
The newer Polaris cleaner models have the serial number stamped on a sticker on the back of the cleaner. If the serial number starts with a “K” it will be a 380, if it starts with “C” it will be a 280, if it starts with a “L” it will be a 360.
How long does a Polaris 280 last?
run the 280 for as long as it keeps the pool clean, this could be 1 hour per day to 6 hours per day depending on the amount of debris is in the pool, but remember the 280 has gears and cogs so the more you run it the quicker it will wear out.
Do I need a booster pump for my pool?
If you intend to use a pressure-side pool cleaner, then you’re going to need a pool booster pump. That’s one of the reasons why you might need a pool booster pump. Beyond that, though, pool booster pumps are invaluable tools that keep your pool running at an adequate water pressure and water flow rate.
Does Polaris pick up dirt?
Polaris Vac-Sweep® 65
Connects to the pressure side of your pool and uses a patented jet sweep assembly to loosen and remove dirt and other particles from hard-to-reach places.
What kind of Polaris do I need?
The newer Polaris cleaner models have the serial number stamped on a sticker on the back of the cleaner. If the serial number starts with a “K” it will be a 380, if it starts with “C” it will be a 280, if it starts with a “L” it will be a 360.
Why do I need a booster pump for pool?
A pool booster pump is an invaluable tool for allowing you to run a pressure-side pool cleaner, and keeping the water pressure and water flow of your swimming pool running steadily and consistently.
How Polaris pool cleaner works?
In these models, the body of the cleaner is hooked up to a hose attached to your water return jet. Water pressure drives the floating cleaner around the surface of your pool. A sweep hose wags along underwater, behind the cleaner, blasting the floor and walls of your pool with jets of water that loosen debris.
Why does Polaris stay in deep end?
Another common cause of flow problems with the 360 is a clogged or dirty pool filter which is not allowing enough flow through the return for the cleaner to operate properly. You may need to backwash or change your sand (clean grids in DE or clean cartridge). If your filter is okay, you may have a clogged impellar.
Why is Polaris tail not moving?
Re: Polaris 360, the tail is not moving…. what do i need… There is a screw that controls the flow through the tail, possible you just need to loosen this to allow more water through. Also it is not uncommon to get a piece of plaster, or other debris stuck inside obstructing the flow.
Why is my Polaris not sinking?
The reason why the cleaner is not sinking may be because you have a “Sand/Silt Bag” on the cleaner to catch the finer debris. When the pours of the bag get plugged, water will not go through, and air will get trapped in the bag and it will cause the cleaner to float.
Can you leave Polaris 9550 in pool?
Just point and direct the 9550 Sport to any desired location in the pool and you will never miss a spot. It is also the only model in the family that features a dirty canister indicator. The 9550 Sport cleans pools up to 60′ in length.
How long should a Polaris run each day?
run the 280 for as long as it keeps the pool clean, this could be 1 hour per day to 6 hours per day depending on the amount of debris is in the pool, but remember the 280 has gears and cogs so the more you run it the quicker it will wear out. On average it should take about 3 hours to clean a standard size pool.
How often should I run my Polaris?
Ideally, you need to run your robot pool cleaner daily or at least once a day if you’re always swimming in it. But if you don’t swim in it as much, run it at least once weekly or every two weeks. When you’re using a swimming pool cover all the time, you may wash your pool monthly.
Why is my Polaris running slow?
LOW PUMP PRESSURE
The pump can be pressure tested by using a Polaris cleaner pressure testing stick and a pressure gauge, placed on the end of the feed hose, to make sure that a problem of sluggish performance is not caused by the booster pump, or a leak or clog along the feed hose.